حقيبة التسوق فارغة، إبدأ التسوق
All Products
The SmartSolar Control Display is a pluggable LCD display for the SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the controller and plug-in the display.
AED180.00
The Victron Filax has been designed to switch sensitive loads, such as computers or modern entertainment equipment from one AC source to another. The priority source typically is the mains, a generator or shore power. The alternate source typically is an inverter. With its switching time of less than 20 milliseconds, sensitive loads will continue to operate without disruption. The Filax is not intended to supply high power household equipment like washing machines or electric motors.
AED1000.00
Simple on-site processing. Accommodating PV cable with different insulation diameters. Mating safety provided by keyed housings. Rated current 40A(2.5-6mm2) Rated voltage 1000v DC Degree of protection IP67 Flame class UL94-VO Safety class Ⅱ Temperature range -40℃~+125℃
AED25.00
Type Solar connector supplied with Male and Female (2 In - 1 Out) Rated current 30A Rated voltage 1000V DC Test voltage 6000V(50Hz, 1min) Overvoltage type/pollution degree CAT Ⅲ /2 Contact resistance of plug connector 1mΩ Contact material : Copper, Tin-plated Insulation material PA/PRO Degree of protection IP67 Flame class UL94-VO Safety class Ⅱ Temperature range -40℃~+110℃
AED50.00
SINGLE CORE CABLES, FOR PHOTOVOLTAIC AND SOLAR SYSTEM USE, ELASTOMERIC COMPOUND INSULATED AND SHEATHED. FLAME RETARDANT, HALOGENFREE AND LOW SMOKE FLEXIBLE CABLES FOR FIXED LAYING, LIFETIME TESTING 20.000 h/120°C Sheath colour: Black Operating temperature: -40 C / 90 C on the conductor Overload temperature: 120 C on the conductor Expected lifetime: >25 years Rated voltage: 1800 V DC Max. temp in case of short circuit: 250 C on the conductor (max. duration 5 seconds) Min. bending radius: 4 x outer diameter of the cable Min. installation temperature: -25 C Max. laying stress during installation: 50N/mm2 STANDARDS: TÜV-Rheinland 2 Pfg 1169/08.2007 IEC 60216-1 IEC 60216-2
AED125.00
Capacity of Fuse : 100A Appr. voltage drop : 60mV Cold resistance : 0.45 mΩ
AED70.00
The galvanic isolator prevents electrolytic corrosion. It blocks low voltage DC currents that enter your boat via the shore power earth wire. These currents can cause corrosion to the boat’s underwater metals, like the hull, propeller, shaft and so on. The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc. The isolator is installed directly behind your boat's 230V connection. The forward voltage from the galvanic isolator is higher than the potential difference between metals. As a result, this voltage will not allow conduction and as such, the galvanic isolator will prevent any electrolytic current. However, if there is a (higher) error voltage in the AC circuit, the diodes will allow current through and the residual-current device will break the circuit.
AED890.00
MEGA-fuse 60A/32V
MEGA-fuse 80A/32V
MEGA-fuse 125A/32V
MEGA-fuse 150A/32V
MEGA-fuse 175A/32V
MEGA-fuse 225A/32V
MEGA-fuse 250A/32V
MEGA-fuse 300A/32V
MEGA-fuse 400A/32V
MEGA-fuse 125A/58V for 48V products
AED100.00
MEGA-fuse 200A/58V for 48V products
MEGA-fuse 250A/58V for 48V products
MEGA-fuse 300A/58V for 48V products
FSP-D40 2P DC SPD Surge protective device, protect against lightning surge voltages in solar system (photovoltaic power supply system). These units must be installed in parallel on the dc networks to be protected and provide common and different modes protection. Its installed location are recommended at both ends of the dc power supply line (solar panel side and inverter/converter side), especially if the line routing is external and long.
AED120.00
FPV-63 2P DC MCB supplementary protectors are designed to provide overcurrent protection within appliances or electrical equipment, where a branch circuit protection is already protection or not required. Devices are designed for direct current (DC) control circuit applications.
It Is a 3 Phase System that Consists • 3 X Multiplus-II 48V/5000VA • 3 X Smart Solar MPPT 250/100 • 4 X Distributor • 1 X Monitoring Device • 1X Touch Display • 4 X BYD Battery-Box Premium LV Flex Lite 5.0kWh/48VDC • it is a portable device that can be shifted easily because of its plug & Play concept with preassembled wheels • it consists 20 Kwh BYD lithium Battery that can be upgraded up to 30kwh inside the trolley • the battery capacity can be extended by using an extra trolley with additional Batteries • It will accept 36 solar panels with 450W with a total capacity of 16.2 Kwp • the trolley has assembled with a 3Phase switch gear & Bypass system in case of solar failure
AED88000.00
FSP-A 4P AC SPD series surge protection device (in short SPD,alias:surge suppressor surge arrester)is suitable for TN-S, TN-C-S, TT, IT etc, power supply system of AC 50/60Hz,<380V, installed on the joint of LPZ1 or LPZ2 and LPZ3. It's designed according to IEC61643-1, GB18802.1, it adopts 35mm standard rail, there is a failure release mounted on the module of surge protection device, When the SPD fails in breakdown for over heat and over-current, the failure rlease will help electric equipments separate from the power supply system and give the indication signal, green means normal, red means abnormal, it also could be replaced for the module when has operating voltage.
AED200.00
FSP-A 2P AC SPD series surge protection device (in short SPD,alias:surge suppressor surge arrester)is suitable for TN-S, TN-C-S, TT, IT etc, power supply system of AC 50/60Hz,<380V, installed on the joint of LPZ1 or LPZ2 and LPZ3. It's designed according to IEC61643-1, GB18802.1, it adopts 35mm standard rail, there is a failure release mounted on the module of surge protection device, When the SPD fails in breakdown for over heat and over-current, the failure rlease will help electric equipments separate from the power supply system and give the indication signal, green means normal, red means abnormal, it also could be replaced for the module when has operating voltage.
AED0.00
FDS-32 dc fuse link A range of 10x38mm fuse links specifically designed for protecting photovoltaic strings. These fuse links are capable of interrupting low overcurrents associated with faulted photovoltaic string arrays (reverse current, multi-array fault).
Solar MC4 crimping
The PA-17 Heavy Duty Linear Actuator provides cost-effective high force capabilities. The stainless steel shaft accompanied by metal gears allows it to push and pull up to 2000 lbs, and hold up to 4000 lbs. The environmental protection rating provides a versatile unit able to withstand dust, water, and harsh environments. The heavy-duty actuator is the only unit in our line of products with adjustable limit switches. This feature allows the user full control over where to start and stop the actuator
AED2700.00
<ol><li><span style="font-size:14px;font-family:Sans-Serif">The 5KVA off-grid solar system is a reliable and efficient solution for those seeking to power their homes or small businesses independently from the grid. With a capacity of 5 kilovolt-ampere, this system is capable of generating and storing enough electricity to meet the daily energy needs of an average household. It consists of high-quality solar panels that harness sunlight and convert it into usable electricity, which is then stored in a battery bank for later use. The system also includes an inverter that converts the stored DC power into AC power, allowing you to power your appliances and devices seamlessly.</span></li><li><span style="font-size:14px;font-family:Sans-Serif">This off-grid solar system is designed to provide a sustainable and eco-friendly alternative to traditional energy sources. By harnessing the power of the sun, you can reduce your carbon footprint and contribute to a cleaner environment. The 5KVA capacity ensures that you have enough power to run essential appliances such as lights, fans, refrigerators, and even small air conditioning units. It is an ideal solution for remote locations, cabins, or areas with unreliable grid connections.</span></li><li><span style="font-size:14px;font-family:Sans-Serif">he system also features a robust battery bank that stores excess energy generated during the day, allowing you to use it during the night or during periods of low sunlight. This ensures a continuous power supply, reducing your reliance on the grid and saving you money on electricity bills.</span></li><li><span style="font-size:14px;font-family:Sans-Serif">The 5KVA Off-grid Solar System is easy to install and requires minimal maintenance. It is built to withstand harsh weather conditions and is equipped with advanced safety features to protect against overcharging, short circuits, and other electrical hazards.</span></li></ol><span style="font-size:14px;font-family:Sans-Serif"></span>
<ol><li><span style="white-space: pre-line; background-color: #ffffff; font-family: "Times New Roman"; font-size: 14px"> </span><span style="white-space: pre-line; background-color: #ffffff; font-family: "Times New Roman"; font-size: 14px">The 10 KVA off-grid solar system is a reliable and efficient solution for those looking to power their homes or businesses independently from the grid. This system is designed to generate and store electricity from the sun, providing a sustainable and cost-effective source of power.</span></li><li><span style="font-family: "Times New Roman"; font-size: 14px"> With a capacity of 10 KVA, this off-grid solar system is capable of powering multiple appliances and devices simultaneously, making it suitable for medium to large-sized households or small businesses. The system includes solar panels, a charge controller, batteries for energy storage, and an inverter to convert the stored energy into usable electricity. </span></li><li><span style="font-family: "Times New Roman"; font-size: 14px">The 10 KVA off-grid solar system is easy to install and requires minimal maintenance, making it a hassle-free option for those looking to reduce their reliance on traditional energy sources.</span></li><li><span style="font-family: "Times New Roman"; font-size: 14px">With its off-grid functionality, this solar system operates independently from the utility grid, utilizing solar panels to harness the sun's energy and convert it into usable electricity. The system includes a set of high-efficiency solar panels, a charge controller, batteries for energy storage, and an inverter to convert the stored DC power into AC power for your electrical needs.</span></li><li><span style="font-family: "Times New Roman"; font-size: 14px">This solar system is designed to be easy to install and maintain, ensuring a hassle-free experience for users. It is built with durable and weather-resistant components, ensuring its longevity and performance even in harsh environmental conditions.</span></li></ol>
<ul><li>The 15kVA Off Grid Solar System is a highly efficient and reliable solution for generating electricity in areas where there is no access to the grid. This system is designed to provide a continuous power supply, making it ideal for remote locations, off-grid cabins, or as a backup power source</li><li>With a capacity of 15 kilovolt-amps (kVA), this off-grid solar system is capable of meeting the energy demands of small to medium-sized homes or businesses. It consists of high-quality solar panels, a charge controller, batteries, and an inverter, all working together seamlessly to convert sunlight into usable electricity. </li><li>The solar panels included in this system are made from durable materials and are designed to withstand harsh weather conditions, ensuring long-lasting performance. The charge controller regulates the charging of the batteries, preventing overcharging and maximizing their lifespan. The batteries store the excess energy generated during the day, allowing you to use it during the night or when the sun is not shining.</li><li>The heart of this off-grid solar system is the inverter, which converts the DC (direct current) electricity stored in the batteries into AC (alternating current) electricity that can be used to power your appliances and devices. The inverter also provides surge protection and ensures a stable and clean power supply, protecting your sensitive electronics from damage.</li><li>The 15kVA Off Grid Solar System offers a sustainable and eco-friendly solution for meeting your energy needs. By harnessing the power of the sun, you can reduce your reliance on fossil fuels and lower your carbon footprint. This system is easy to install and requires minimal maintenance, making it a cost-effective and hassle-free choice for those looking to go off-grid or have a reliable backup power source. </li></ul>
AED28000.00
Ultra - fast Maximum Power Point Tracking (MPPT)\ - Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result i s often that the battery will continually be cycled between a partially charged state and the end of discharge state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Batter Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Modern Apple and Android smartphones, tablets, macbooks and other devices: see the VE.Direct Bluetooth Smart dongle and the MPPT app discovery sheet for screenshots. ColorControl panel
Features: Ultra - fast Maximum Power Point Tracking (MPPT)\ - Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result i s often that the battery will continually be cycled between a partially charged state and the end of discharge state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Batter Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week. Programming, real-time data and history display options Modern Apple and Android smartphones, tablets, macbooks and other devices: see the VE.Direct Bluetooth Smart dongle and the MPPT app discovery sheet for screenshots. ColorControl panel
Ultra-fast maximum power Point tracking (mppt) Advanced maximum power Point detection in case of partial shading conditions Battery life: intelligent Battery Management by load shedding Bluetooth enabled (Bluetooth dongle needed) Day/night timing and light dimming Option
Ultra-fast maximum power Point tracking (mppt) Advanced maximum power Point detection in case of partial shading conditions Battery life: intelligent Battery Management by load shedding Bluetooth enabled (Bluetooth dongle needed) Day/night timing and light dimming Option.
A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life. By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvestby up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Battery voltage 12 / 24 / 48V Auto Select (software tool needed to select 36V) Rated charge current 85A Maximum PV power, 12V 1200W Maximum PV power, 24V 2400W Maximum PV power, 48V 4900W Max. PV short circuit current 70A (max 30A per MC4 conn.) Maximum PV open circuit voltage : 250V absolute maximum coldest conditions Maximum efficiency 99% Self-consumption Less than 35mA @ 12V / 20mA @ 48V Charge voltage 'absorption' Default setting: 14,4 / 28,8 / 43,2 / 57,6V (adjustable with: rotary switch, display, VE.Direct or Bluetooth) PV terminals : Three pairs of MC4 connectors (MC4 models) Battery terminals 35 mm² / AWG2 Protection category IP43 (electronic components), IP22 (connection area) Weight 4,5kg Dimensions (h x w x d) in mm 246 x 295 x 103
Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvestby up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. VE.Can: the multiple controller solution Up to 25 units can be synchronised with VE.Can Advanced Maximum Power Point Detection in case of partial shading conditions If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP. Outstanding conversion efficiency No cooling fan. Maximum efficiency exceeds 99%. Operating temperature -30 to +60°C (full rated output up to 40°C) Humidity 95%, non-condensing Maximum altitude 5000m (full rated output up to 2000m) Environmental condition Indoor, unconditioned Pollution degree PD3 Data communication VE.Can, VE.Direct and Bluetooth Battery voltage 12 / 24 / 48V Auto Select (software tool needed to select 36V) Rated charge current 100A Maximum PV power, 12V 1450W Maximum PV power, 24V 2900W Maximum PV power, 48V 5800W Max. PV short circuit current 70A Maximum PV open circuit voltage : 250V absolute maximum coldest conditions Maximum efficiency 99% Self-consumption Less than 35mA @ 12V / 20mA @ 48V Charge voltage 'absorption' Default setting: 14,4 / 28,8 / 43,2 / 57,6V (adjustable with: rotary switch, display, VE.Direct or Bluetooth) PV terminals 3) 35 mm² / AWG2 (Tr models) Battery terminals 35 mm² / AWG2 Protection category IP43 (electronic components), IP22 (connection area) Weight 4,5kg Dimensions (h x w x d) in mm 216 x 295 x 103
Ultra-fast Maximum Power Point Tracking (MPPT) Solar Charge Controller The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required. Multiple independent MPPT tracking inputs With multiple MPPT trackers, you can optimize your solar panel design for maximum performance for your specific location. Isolated PV connections for additional safety Full galvanic isolation between PV and battery connections provide additional overall system safety. Wide MPPT voltage range 80 – 450 VDC PV operating range, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful charger weighs only 7.9 kg for the 100A model. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation. Display and Bluetooth The display reads battery, and solar charge controller parameters. The parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. PV Isolation resistance monitoring for peace of mind at higher voltages The MPPT RS continuously monitors the PV array and can detect if there are faults that reduce the isolation of the panels to unsafe levels. VE.Can and VE.Direct port For connection to a GX device for system monitoring, data logging, and remote firmware updates. VE.Can allows for up to 25 units to be connected together in parallel and synchronize their charging. I/O Connections Programmable Relay, temperature sensor, auxiliary, digital input and voltage sensor connections. The remote input can accept the Victron smallBMS, and other BMS with allow-to-charge signal.
Liquid crystal display : For status monitoring and set-up Load output : Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual. The connect and disconnect voltages are adjustable. Day/night timing of the load output : This option allows for a pre-set ON-time after dusk. Programmable battery charge algorithm : Preprogrammed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (with internal BMS only) Two 5 Volt USB outputs : Maximum current (both outputs combined): 2A Battery Voltage 12/24 V with automatic system voltage detection Rated charge current 30A Automatic load disconnect Yes Maximum solar voltage 28V / 55V (1) Self-consumption < 10 mA Load output Manual control + low voltage disconnect +timer Protection : Battery reverse polarity (fuse) , Output short circuit, Over temperature Overload protection : Shut down after 60 s in case of 130% load Shut down after 5 s in case of 160% load Short circuit: immediate shut down Grounding : Common positive Operating temp. range -35 to +60°C (full load) Protection class IP20 Terminal size 16mm² / AWG6 Weight 0,3kg Dimensions (h x w x d) 101x184x47mm
Easily mount a BMV and MPPT Control on a wall.
Off-Grid solar inverter : The Inverter RS Smart Solar 48/6000 is a 48V 6kVA Inverter with 450VDC 4kWp PV input. It is used in off-grid solar applications where AC power is required. Combination of an inverter, bi-directional DC-DC converter and MPPT The inverter produces a perfect sine wave, able to supply high powered appliances. It is supplied by a bi-directional DC-DC converter, that can either charge the battery when excess solar power is available or convert from the battery when it is needed. Wide MPPT voltage range 80 – 450VDC, with a 120VDC PV startup voltage. Light weight, efficient and quiet Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. Display and Bluetooth : The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other Bluetooth enabled device. In addition, Bluetooth can be used to set up the system and to change settings with VictronConnect. Support for AC and DC coupled PV battery charging : The Inverter RS supports the connection of AC coupled PV inverters on the AC output up to 6kVA, and a total battery charging capacity of up to 100A. Frequency Shift Power Control is enabled out of the box, without the need for configuration, reducing installation time. INVERTER DC Input voltage range 38 – 64 V (6) Output Output voltage: 230 VAC ± 2% Frequency: 50 Hz ± 0.1% (1) Continuous output power at 25°C Increases linearly from 4800 W at 46 VDC to 5300 W at 52VDC Continuous output power at 40°C 4500W Continuous output power at 65°C 3000W Peak power 9 kW for 3 seconds Short-circuit output current 50A Maximum efficiency 96.5% at 1 kW load and 94% at 5 kW load SOLAR Maximum DC voltage 450V Nominal DC voltage 300V Start-up voltage 120V MPPT operating voltage range 80 – 400V (5) Maximum DC input current 18A (4) Maximum PV input power 4000W Maximum DC charging power 4000W CHARGER Charge voltage 'absorption' (V DC) 57.6V Charge voltage 'float' (V DC) 55.2V Maximum charge current 100A Battery temperature sensor Yes Parallel and 3-phase operation : NO Programmable relay (3) Yes Protection (2) a - f Support AC Input from Grid / Generator : NO (Have to use Battery Charger, Please refer Datasheet /Manual) Operating temperature range -40 to +65°C (fan assisted cooling) Protection category IP22 Battery-connection M8 bolts 230 V AC-connection Screw terminals 13 mm² (6 AWG) Weight 11 kg Dimensions (hxwxd) 425 x 440 x 125 mm REMARKS :: 1) Can be adjusted to 60 Hz 2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) 230 VAC on inverter output 3) Programmable relay which can be set for general alarm, DC under voltage or genset start/stop function. DC rating: 4A up to 35VDC and 1A up to 70VDC 4) Normal operation is regulated to 18A, with maximum reverse polarity protection 40A. 5) MPPT operating range is also constrained by battery voltage - PV VOC should not exceed 8x battery float voltage, e.g. a 50V battery voltage maximum should have 400V maximum PV array. – see product manual for further information. 6) Minimum start-up voltage is 41V. Inverter shutdown can be set as low as 32V DC, but may shut down on low AC output voltage (due to load). Over-voltage disconnect is 65.5V. Charger setpoint can be set to max 62V. The charge current derates above 57V.
The Multi RS Solar 48/6000 is a 48V 6kVA Inverter/Charger with 450VDC 4kWp PV input. Thanks to high frequency technology and a new design this powerful inverter weighs only 11kg. In addition to this it has an excellent efficiency, low standby power, and a very quiet operation.
The all-in-one solar power solution The Victron EasySolar-II GX integrates the following elements: • A MultiPlus-II inverter/charger 3KVA • A SmartSolar MPPT -Tr solar charge controller 4000W • A GX device with a 2 x 16 character display. These elements come prewired together inside a single unit. This greatly simplifies most installations, saving time and money.
The EasySolar combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring. All-in-one solar power solution The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring The solar charge controller: Blue Solar MPPT 100/50 Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors. The inverter/charger: MultiPlus Compact 24/1600/40 The MPPT charge controller and the MultiPlus Compact inverter/charger share the DC battery cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset. AC distribution The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and two 16A circuit breakers. One 16A output is controlled by the AC input: it will switch on only when AC is available. PowerAssist Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed. Unique solar application software Several software programs (Assistants) are available to configure the system for various grid interactive or stand-alone applications.
All-in-one solar power solution The EasySolar combines a MPPT Solar Charge Controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring. Color Control panel Two outstanding functions: - Prioritizes battery charging by the MPPT charge controller - Connects to the internet, enabling remote monitoring (VRM website) and remote control. AC distribution The AC distribution consists of a RCD (30mA / 63A) and four AC outputs protected by two 10A and two 16A circuit breakers. An additional 16A output is controlled by the AC input: it will switch on only when AC is available. PowerAssist Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed. Unique solar application software Several software programs (Assistants) are available to configure the system for various grid interactive or stand-alone applications.
يرجى ادخال بريدك الإلكتروني المرتبط بالحساب وسيتم ارسال رابط لإعادة ضبط كلمة المرور.
