حقيبة التسوق فارغة، إبدأ التسوق
All Products
FUSE Holder for MIDI Fuse ( Fuse has to Purchase separately ). Fuse holder is suitable for below models CIP132060010 MIDI-fuse 60A/32V (package of 5 pcs) CIP132080010 MIDI-fuse 80A/32V (package of 5 pcs) CIP132100010 MIDI-fuse 100A/32V (package of 5 pcs)
AED40.00
Modular single fuse holders, for MEGA fuses only
AED50.00
Fuse for FUSE HOLDER FOR MEGA-FUSE
AED110.00
ANL fuse 400A/80V Appr. voltage drop 125 mV Cold resistance 0,3 mΩ
Fuse holder for ANL-fuse
MEGA-fuse 500A/32V
AED25.00
Busbar 250 A with cover Max. current rating 250 A Max. Voltage rating 70 VDC Terminal diameter 5/16 inch / 8 mm Terminal height 0.67 inch / 17 mm Terminal material Stainless steel Hex nut material Tin-plated copper Recommended torque 110 lbf·inch / 13 N·m Busbar strip material Tin-plated copper (5 x 24 mm) Base material ABS, black, UL 94 V-0 Cover material ABS, black, UL 94 V-2 Weight, 4 terminals 1.0 lb / 0,45 kg Dimensions (hxwxd) (with cover) 48 x 237 x 70 mm
AED220.00
A modular DC bus bar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. Contains a positive and negative bus-bar and provides a connection for 4 individual DC equipment circuits, loads or DC groups. It has a space for individual DC fuses per DC group. There is an optional feature of an LED for each fuse to indicate if fuse is blown. When all is OK, only the central LED is green; when a fuse has blown (or is missing) the central and blow fuse circuit LEDs turn red. If you are not using all connection points in your DC distribution, it may be necessary to fit dummy fuses to extinguish the red LEDs. Fuses Uses MEGA fuses. Please note that some MEGA fuses are only rated to 36Volt (suitable for 24V systems), You must use 58/64V rated fuses for 48V systems.
AED0.00
B2B Chargers (battery to battery/DC to DC Chargers). For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch. Input voltage range (1) 10-17V Under voltage shut down 7V Under voltage restart 7,5V Nominal output voltage 12,2V Output voltage adjust range 10-15V Output voltage tolerance +/- 0,2V Output noise 2mV rms Cont. output current at nominal output voltage and 40°C : 30A Maximum output current (10 s) at nominal output voltage : 40A Short circuit output current 60A Cont. output power at 25°C 430W Cont. output power at 40°C 360W Efficiency 87% No load input current < 80mA Standby current Less than 1mA Operating temperature range -20 to +55°C (derate 3% per °C above 40°C) Humidity Max. 95% non-condensing DC connection Screw terminals : Maximum cable cross-section 16 mm² (AWG6) Weight : 1.8 kg
B2B Chargers (battery to battery/DC to DC Chargers) For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch. Input voltage range (1) 20-35V Under voltage shut down 14V Under voltage restart 15V Nominal output voltage 12,2V Output voltage adjust range 10-15V Output voltage tolerance +/- 0,2V Output noise 2mV rms Cont. output current at nominal output voltage and 40°C : 30A Maximum output current (10 s) at nominal output voltage : 45A Short circuit output current : 60A Cont. output power at 25°C : 430W Cont. output power at 40°C : 360W Efficiency 88% No load input current 100mA Operating temperature range -20 to +55°C (derate 3% per °C above 40°C) Humidity Max. 95% non-condensing DC connection Screw terminals : Maximum cable cross-section 16 mm² (AWG6) Weight : 1,8 kg
DC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. The Buck-Boost DC-DC Converter is a DC-DC converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Since, when the engine is running, these dynamos (powered by the on-board electronics of Euro 5 and 6 engines) do not always emit the correct charging current, a DC-DC converter is essential for charging the service battery properly. DC-DC Converter for charging a 12V or 24V service battery in vehicles with a smart alternator (regenerative braking, Euro 5 and Euro 6 engines) The Buck-Boost DC-DC Converter is a DC-DC Converter for charging a 12V or 24V service battery in vehicles with a smart alternator. The converter will charge the auxiliary battery with a pre-set charge voltage, eliminating high voltages (e.g. Mercedes: 15,4V) and low voltages. Input voltage range 10-30V Under voltage threshold 10V Output voltage range 10-30V Maximum charge current 12V : 100A and 24V : 50A Power consumption Converter off, LEDs off (power save mode) 7 mA On/off input (pin 1, purple wire) ‘On’ threshold voltage > 2V Maximum input voltage 30V Output pin 1 and pin 2 Output voltage if activated Vpinout = Vin Maximum current (per pin) Ipinout = 1A Operating temperature range -25 +60°C Ambient temperature Max current: up to 60°C Weight 4,1kg Dimensions 288 x 162 x 95mm
The Orion XS, engineered from the ground up, redefines DC-DC battery-to-battery charging. Ideal for dual battery systems charged by an intelligent alternator. This device not only ensures top-tier performance but also guarantees the safety of your system. Stay in charge with configurable input and output currents and rest assured that your Orion XS will run at full capacity up to 40°C. The 98,5% efficient aluminium circuit board technology means less heat, without the need for fans. As an integral part of your Victron system, the Orion XS offers full (remote) monitoring and control capabilities, giving you complete command of your device and system.
Victron Energy Orion DC-DC converter - 12v in 24v out - 20A - Standard ground version. Voltage converter which steps up from 12vdc to 24vdc. used in applications where 24vdc equipment is required on a 12vdc vessel - 20amp version An ever-increasing amount of electrical equipment is being used on vehicles and boats. Most low-voltage equipment, such as navigation, radios, mobile telephones or car hi-fi systems, are designed for 12 Volts. Victron Energy supplies DC/DC converters which deliver a stable 12 Volt supply from a 24 Volt system. These products are also distinguished by high efficiency, together with absolute safety. An inferior supply can cause irreparable damage to your 12 Volt system, but the use of an Orion voltage converter can prevent such problems. Features Input voltage range: 9-18 V Undervoltage shutdown / restart: 8V / 10V Output voltage: Adjustable (with potentiometer) 20–30V F set 26,4V V Efficiency: 93% Suitable to buffer-charge a battery Continuous / Max output current: 20A / 30A Off load current: < 30mA Operating temperature range (derate 3% per °C above 40°C): -20 to +55°C DC connection: M6 Bolts Other features include Fan assisted cooling (temp. controlled), Remote on-off, Can be connected in parallel Related Products
High efficiency Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection When installed with the screw terminals oriented downwards Screw terminals No special tools needed for installation Specification : Input voltage range 18-35 V Output voltage 12.7 V Efficiency 95% Continuous output current 5 A Max. Output current 7 A Galvanic isolation no Off load current < 20 mA Operating temperature range (derate 3% per °C above 40°C) -20 to +55°C DC connection : Screw terminals Maximum cable cross-section 3,3 mm² AWG12 Weight kg 0,09 Dimensions hxwxd in mm 53x51x27
High efficiency Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection When installed with the screw terminals oriented downwards Screw terminals No special tools needed for installation Specification : Input voltage range 18-35 V Output voltage 12.5 V Efficiency 97% Continuous output current 10 A Max. Output current 12 A Galvanic isolation no Off load current < 45 mA Operating temperature range (derate 3% per °C above 40°C) -20 to +55°C DC connection : Screw terminals Maximum cable cross-section 6 mm² AWG10 Weight kg 0,2 Dimensions hxwxd in mm 73x94x37
High efficiency Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection When installed with the screw terminals oriented downwards Screw terminals No special tools needed for installation Specification : Input voltage range 18-35 V Output voltage 12.5 V Efficiency 97% Continuous output current 20 A Max. Output current 25 A Galvanic isolation no Off load current < 45 mA Operating temperature range (derate 3% per °C above 40°C) -20 to +55°C DC connection : Screw terminals Maximum cable cross-section 6 mm² AWG10 Weight kg 0,2 Dimensions hxwxd in mm 73x94x37
Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm Specifications: - Input voltage range (V) 18-35 - Under voltage shutdown (V) 14 - Under voltage restart (V) 18 - Output voltage adjustable with potentiometer yes - Output voltage (V): Adjustable 10–15V F set 13,2V - Efficiency (%) 92 - Suitable to buffer-charge a battery : yes - Can be connected in parallel : yes - Continuous output current (A)70 - Max. Output current (A) 85 - Operating temperature range(derate 3% per °C above 40°C) -20 to +55°C - Off load current < 20mA - Remote on-off yes - Dimensions hxwxd in mm 65x88x195 - Weight kg: 0,85
Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3mm Specifications: - Input voltage range (V) 9-18 - Under voltage shutdown (V) 8 - Under voltage restart (V) 10 - Output voltage adjustable with potentiometer yes - Output voltage (V): Adjustable 20–30V F set 26,4V - Efficiency (%) 95 - Suitable to buffer-charge a battery : yes - Can be connected in parallel : yes - Continuous output current (A)10 - Max. Output current (A) 20 - Operating temperature range(derate 3% per °C above 40°C) -20 to +55°C - Off load current < 15mA - Remote on-off : No - DC connection Faston tabs 6.3 mm - Dimensions hxwxd in mm 45x90x125 - Weight kg: 0.4
Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). Adjustable output voltage: can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) On 12V and 24V input models only. Specification Input voltage range 20-35V Under voltage shut down 14V Under voltage restart 15V Nominal output voltage 24,2V Output voltage adjust range 20-30V Output voltage tolerance +/- 0,2V Output noise 2mV rms Cont. output current at nominal output voltage and 40°C 17A Maximum output current (10 s) at nominal output voltage minus 20% : 25A Short circuit output current 40A Cont. output power at 25°C 480W Cont. output power at 40°C 400W Efficiency 89% Off load current < 80mA Galvanic isolation 200V dc between input, output and case Operating temperature range -20 to +55°C (derate 3% per °C above 40°C) Humidity Max. 95% non-condensing DC connection Screw terminals Maximum cable cross-section 13 mm² (AWG6) Weight 1.6 kg Dimensions hxwxd : 130 x 186 x 70 mm
Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). Adjustable output voltage: can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) On 12V and 24V input models only. Specification Input voltage range 20-35V Under voltage shut down 14V Under voltage restart 15V Nominal output voltage 24,2V Output voltage adjust range 20-30V Output voltage tolerance +/- 0,2V Output noise 2mV rms Cont. output current at nominal output voltage and 40°C 12A Maximum output current (10 s) at nominal output voltage minus 20% : 15A Short circuit output current 30A Cont. output power at 25°C 320W Cont. output power at 40°C 280W Efficiency 89% Off load current < 80mA Galvanic isolation 200V dc between input, output and case Operating temperature range -20 to +55°C (derate 3% per °C above 40°C) Humidity Max. 95% non-condensing DC connection Screw terminals Maximum cable cross-section 13 mm² (AWG6) Weight 1.6 kg Dimensions hxwxd : 130 x 186 x 70 mm
Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). Adjustable output voltage: can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Input fuse (not replaceable) On 12V and 24V input models only. Specification Input voltage range 20-35V Under voltage shut down 14V Under voltage restart 15V Nominal output voltage 24,2V Output voltage adjust range 20-30V Output voltage tolerance +/- 0,2V Output noise 2mV rms Cont. output current at nominal output voltage and 40°C 5A Maximum output current (10 s) at nominal output voltage minus 20% : 6.3A Short circuit output current 30A Cont. output power at 25°C 120W Cont. output power at 40°C 115W Efficiency 87% Off load current < 60mA Galvanic isolation 200V dc between input, output and case Operating temperature range -20 to +55°C (derate 3% per °C above 40°C) Humidity Max. 95% non-condensing DC connection Screw terminals Maximum cable cross-section 6 mm² (AWG6) Weight 0.42 kg Dimensions hxwxd : 100 x 113 x 47 mm
Completely encapsulated: waterproof, shockproof and ignition protected Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin.
DC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. The Buck-Boost DC-DC Converter is a DC-DC converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Since, when the engine is running, these dynamos (powered by the on-board electronics of Euro 5 and 6 engines) do not always emit the correct charging current, a DC-DC converter is essential for charging the service battery properly.
Remote on-off connector The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel.
يرجى ادخال بريدك الإلكتروني المرتبط بالحساب وسيتم ارسال رابط لإعادة ضبط كلمة المرور.
